New Method: How to Reset ADT Alarm System Without Code

Leave a comment

For everyone who wants to reset ADT alarm system without code, you have to know that the method to do that varies according to the brand of the system. In this post, you will be able to find the way to reset the MASTER alarm code by using a method to turn the alarm panel off or on and set the installer code that can be used to set a new master code.

How do you identify the ADT system? The type of ADT security system can be identified easily by looking at the metal alarm panel. It is where you are able to find a circuit board that has a chip with a sticker that is written WA3000 or WA30001 on it.

New Method How to Reset ADT Alarm System Without Code

If you want to disarm the system and change the master, the first thing that you need to do is to set an installer security code. Here is step by step to follow to be able to make the installer code:

    1. First of all, you have to disconnect the backup battery that is found inside the panel.
    2. After finding the backup battery, unplug the power from the outlet.
    3. Do not forget to make sure that the system is off.
    4. When you are confident with it, it is time for you to plug the power back to the system.
    5. Then, wait for a total of 60 seconds or a minute.
    6. Once the time passes, the next thing that you need to do is to press and hold the * and # keys at the same time.
    7. It is also needed for you to check if the installer code is asked by the keypad.
    8. If it is, press *20 followed by a 4 digit code of your choice.
    9. After that, wait for the beep sound to be heard as a confirmation.
    10. Upon hearing the confirmation beep, press *99 to exit the programming mode.
    11. When everything is done, the next thing that you can do is to use the installer code so that you can set the master code.

How do you set the master code? This kind of code is apparently able to be set on your ADT system by using the alarm keypad. If you have no idea how to do it, below are all the instructions to follow:

    1. Firstly, you have to enter the installer code + 802 and follow it with the 4 digit code.
    2. After entering these two, you can just wait for the confirmation beep to be heard.
    3. Just like that now you have your master code working on your security system.
    4. Do not forget to test it in order to make sure that you are able to arm the system.

After following the guide, now you have the master code for your security system in your hand and the keypad is able to be used to arm or disarm the alarm. It is worth noting to make sure to that both the doors and the windows are all closed. Aside from that, do not forget to also test the master code as well as the user codes. Apparently, the master code is also able to be used to make user codes.

It should be easy for you to reset the ADT alarm system even if there is no code just by following the guide above. Try to seek help from the professionals in case you are having a hard time.

Talking about the ADT alarm system, apparently, a typical ADT security alarm system is between 100 and 115 decibels? Can you imagine how loud it is? With the sound that is produced by it, you might get nagged by your neighbors and then you might want to turn it off. However, the issue arises when you do not have the code. Is it possible to turn it off without a code?

Turning off the ADT alarm system even without a code is possible. Depending on the type of the system, here are some options to choose from, including locating and removing the transformer unplug from the outlet, disassembling the security panel, and removing the backup battery

The ADT security systems vary. While there are different, all of them essentially follow the same routine. There is a panel box in many of the older ones and it is separate from the keypad. The panel box is the one where the battery if found. After unplugging the large, square plug that is usually screwed into the power outlet called the transformer, it will be needed for you to get the access to the panel box. For those who currently live in a home that has installed the system in the past, it is possible for the panel box to not be able to be accessed through the traditional methods, such as a key. You will need to find out how to access the battery with the exception if the previous owner or renter provided you with one.

Just like how 9-volt batteries attach to a plastic or rubber flap with both a positive and negative terminal, the battery is usually attached by two leads. All that you have to do is to disconnect it and after the transformer is unplugged, the alarm should stop. In case there is no way for you to find the transformer or if it is screwed in, it is better for you to just cut the power from the circuit breaker. Then, get rid the battery. When everything is done, it is time for you to find and remove the transformer.

Talking about the battery, you have to know that some of them will be found in the security panel itself. They are adjacent to the keypad or directly behind it. There are a few kinds of ADT home security systems and most of them are Honeywell products, which is now known as Residio. Each of them has a battery backup and each of them draws the main power from an AC outlet.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *